A new industrial chemical means an industrial chemical that is not listed on the Australian Inventory of Chemical Substances (AICS). Some chemicals listed on the AICS may be subject to conditions of use. These chemicals are also defined as new industrial chemicals if their use is for other than that stated on AICS.

 

A chemical that is a reaction intermediate or an incidentally produced chemical is not considered a new industrial chemical.

 

All new industrial chemicals must be notified to NICNAS, and an assessment certificate or permit obtained before they can be imported and/or manufactured in Australia. Certain new industrial chemicals are considered exempt from notifying to NICNAS but are subject to reporting requirements.

 

Certificates

 

New chemicals can only be introduced by the holder of an assessment certificate, unless the chemical is covered by a permit or under specific NICNAS exemptions.

 

Five years after assessment, and in some cases sooner, the chemical is listed on AICS and is available for open use. The assessment report is provided to the notifier, who is able to use the report to support their responsibilities for control of the chemical, for example, State and Territory hazardous substances legislation, environmental legislation and Poisons Scheduling.

 

The full public report, including recommendations on safe use, is available to the public on the NICNAS web site (www.nicnas.gov.au) and may be used by State and Territory agencies and in the workplace.

 

Commercially sensitive information may be exempt from publication in the full public report if the commercial interest outweighs the public interest. Summary reports of each assessment are published in the Chemical Gazette.

 

Several certificate notification categories are available:

 

Standard Notification (STD)

 

Required for all new industrial chemicals and biopolymers where the volume introduced is greater than 1,000 kg/year, and new polymers with a number-average molecular weight less than 1,000 daltons (except certain polyesters of low risk). This category requires the highest level of data, including toxicological and ecotoxicological test data, chemical identity, physicochemical properties, use pattern, occupational, environmental and public exposure information, environmental fate data, material safety data sheet and label.

 

Limited Notification (LTD)

 

These are required for all new industrial chemicals and biopolymers where the volume introduced is less than 1,000 kg/year (or 10 tonne/year in the event that they are manufactured in Australia, solely for the purpose of further manufacture at the same site) and new synthetic polymers with a number-average molecular weight greater than 1,000 daltons. Data requirements are less than for a standard notification, but include chemical identity, physico-chemical properties, use pattern, occupational, environmental and public exposure, MSDS and label. All available data must be provided.

 

Polymers of Low Concern (PLC)

 

These chemicals are defined by predetermined criteria to be of low hazard to humans and the environment. They can be introduced to Australia with reduced fees and reduced data requirements.

 

Extension of original assessment certificate (EXT)

 

The original assessment certificate can be extended to include other introducers, providing the original certificate holder agrees in writing. In addition to specific data requirements, new information on exposure or adverse health and environmental effects must be provided.

 

Self assessment (SAPLC/SANHC/SANHP)

 

Audited self-assessment allows industry to self-assess low regulatory concern chemicals against specified criteria and provide an assessment report that is screened and adopted by NICNAS.

 

This category is available for Polymer of Low Concern (SAPLC) and Non-hazardous chemicals (SANHC) and non-hazardous polymers (SANHP) other than PLC. The holder of a self-assessment certificate must keep relevant records and report to NICNAS’ Director annually.

 

Permits

 

Permits allow chemicals to be introduced conditionally, without a full assessment, providing certain information is provided on identity, hazard and exposure. Material safety data sheets and labels must also be provided. NICNAS assesses permit applications under shorter timeframes and reduced fees.

 

Several permit categories are available:

 

Commercial Evaluation Category (CEC)

 

Chemicals to be introduced solely for determination of their commercial potential are eligible for assessment as CECs. The application can be for introduction of up to 4,000 kg for up to two years, provided that the quantity and timeframe requested by the notifier can be justified as necessary for commercial evaluation purposes. Data requirements include health and environmental effects information, chemical identity, use and distribution arrangements, volume and duration of introduction, occupational, environmental and public exposure, material safety data sheets and label. Customer agreements must be provided for each proposed user of the chemical. There are annual reporting obligations.

 

Low Volume Chemicals (LVC)

 

LVCs are available for chemicals introduced at 100 kg/year. Data requirements include health and environmental effects information, chemical identity, use, volume and duration of introduction, occupational, environmental and public exposure, material safety data sheet and label. The maximum LVC permit period is three years, with the provision for unlimited renewal. Annual reporting obligations apply.

 

Export only permit (EOP)

 

Industrial chemicals introduced under the following scenarios are eligible for the Controlled Use Permits (Export Only):

 

•           importation of a new chemical into Australia for export of entire quantity

•           or importation of a new chemical into Australia for use in formulation of products for export of entire quantity; or manufacture of a new chemical  in Australia for export of entire quantity, or

•           manufacture of a new chemical in Australia for use in formulation of products for export of entire quantity.

 

The Controlled Use Permit (Export Only) is available for chemicals where low risk can be demonstrated.

 

Early Introduction Permit for Non – Hazardous Chemicals (EIP)

 

Applications for an EIP must be made in conjunction with an application for a certificate. EIPs are available for introducing chemicals that are not hazardous to human health and the environment. Once an EIP is granted, the applicant may introduce the chemical according to permit conditions before the full assessment has been completed. Factors taken into account include reasonable protection of occupational health, public health and the environment.

 

Exemptions

 

Some low regulatory concern chemicals are exempt from notification to NICNAS even if they are new industrial chemicals. Chemicals suitable to be introduced under an exemption are as follows:

 

Research, development or analytical (RD&A) purposes

 

RD&A chemicals that are imported or manufactured in volumes of not more than 100 kg/year do not require notification but are subject to annual reporting obligations. At higher volumes, the same provisions apply as for other new chemicals and polymers. An exception applies in certain specific cases where an RD&A chemical is manufactured in Australia in situations where smaller volumes cannot be manufactured. For example, there may be limitations on the size of equipment available for manufacture. In these cases, information must be provided to NICNAS on the type and location of the apparatus (a fixture), the program of work, type of chemical and procedures for safe disposal of the chemical and any hazardous degradation products.

 

Low volume/other exemptions

 

New industrial chemicals are exempt from notification if introduced:

 

•           at a port or airport in Australia, remains subject to the control of customs at the port or airport at all times and leaves Australia less than 30 days after the day of introduction

•           in quantities of not more than 10 kg in a period of 12 months, is for cosmetic use, poses

•           no unreasonable risk to occupational health, public health or the environment, and meets certain safeguards

•           in a cosmetic product at a concentration at 1% or less, and is non-hazardous

•           in quantities not exceeding 100 kg in a period of 12 months, is for non-cosmetic use, and poses no unreasonable risk to occupational health, public health, or

•           in an amount that is greater than 10 kg but not exceeding 100kg in a period of 12 months, is for cosmetic use, and poses no unreasonable risk to occupational health, public health or the environment.

 

Note: Introducers under these exemption categories, self assessment, and certain permits must keep in writing, for five years after the introduction, all information available to the person about occupational health and safety, public health matters and the environmental effects of the chemical. In addition, introducers of chemicals in this category should complete an annual report form and return it to NICNAS before or on 28 September of the following registration year.